TRAINING
MANUAL
TRAINING VIDEOS AVAILABLE AT
YOUTUBE.COM/NICTRAINING
WWW.CERAKOTEGUNCOATINGS.COM
PLEASE READ
Cerakote™ Firearm Coatings are designed for professionals
and should be applied by NIC-trained applicators and coating
professionals with proper training and equipment. This train-
ing manual is intended to be used as a supplemental guide
for certified and professional applicators ONLY. It is critical
to follow all instructions in this manual. If for any reason you
are not willing to, or cannot follow the steps in this manual,
do not attempt to coat any product using Cerakote™, or any
other NIC product. If you have any questions, please contact
NIC Industries.
Thank you
Cerakote Firearm Coatings
A Division of NIC Industries, INC.
866-774-7628
www.CerakoteGunCoatings.com
1
WWW.CERAKOTEGUNCOATINGS.COM
NOTES
2
WWW.CERAKOTEGUNCOATINGS.COM
NOTES
3
WWW.CERAKOTEGUNCOATINGS.COM
Phase 1: Disassemble
Disassemble:
Completely disassemble the firearm.
Detail strip your firearm. If you are unfamiliar with this
level of disassembly have a certified gunsmith perform
the disassembly and reassembly.
Take a photograph of all the parts received. Make note of
the substrate type on each piece (i.e: Steel, Aluminum,
plastic, composite, polymer, etc.) 4
WWW.CERAKOTEGUNCOATINGS.COM
Phase 2: degrease
Degrease:
Soak each part for 10-15 minutes in a non-water based degreaser such as Brake-Kleen®
(NIC Part # SE-174) or acetone. Spraying is not sufficient; soaking is required.
Allow parts to air dry after soaking.
From this point on it is critical to avoid touching the parts with your bare hands.
Use powder-free latex style gloves to handle the parts.
5
WWW.CERAKOTEGUNCOATINGS.COM
Phase 3: surface-prep
Surface Prep:
Begin by plugging the bore at both the chamber and the muzzle end of the barrel prior
to blasting. Grit blast the parts with #100 to #120 grit aluminum oxide or garnet sand
at 80 to 100 psi. Strive for an even blast pattern over the surfaces of the parts. Lightly
blast (30-40 psi) non-metal parts such as: wood, plastic or polymer.
TIP:
• If the part’s surface is still shiny
after blasting, you haven’t blasted
enough.
• If you use too coarse of grit, the
microscopic valleys on the part’s
surface will be too deep for the 1.0
mil (.001”) coating to completely
fill while covering the correspond-
ing “peaks” sufficiently to assure a
satisfactory coating.
• Don’t use sand that has been
previously used to clean dirty,
greasy or oily parts. Doing so will
contaminate your parts.
CAUTION:
• If you use #120 grit, be sure the grit does not wear out
as you are using it. #120 is pretty fine at the start, and
will wear to an ineffective dust.
• Do not use glass beads. Glass beads dimple the sur-
face rather than etching it, and will not yield a sufficient
blast profile for optimum coating adhesion. 6
WWW.CERAKOTEGUNCOATINGS.COM
Phase 4: racking/masking
Racking:
Hang or otherwise fixture your parts so that you can access all the surfaces of each
part with your HVLP gun.
*REMEMBER TO ALWAYS WEAR POWDER-FREE, LATEX-STYLE GLOVES.
AR 15 Lower Receiver
Correct Racking
Techniques
Remington 700 Receiver Stripped Springfield 1911
Frame
Welding wire used to
suspend parts
7
WWW.CERAKOTEGUNCOATINGS.COM
g Phase 4: masking & racking supplies
Recommended Masking & Racking Supplies:
The following products can be purchased at www.CerakoteGunCoatings.com
Cerakote Starter Racking,
Masking and Camo Kit:
Great starter kit with a starting
quantity of racking, masking
and camo products.
NIC part # SE-175
Kit Includes
-Various high temp plugs for
nearly any caliber barrel
-A variety of metal hooks for
most racking situations
-A small spool of racking wire
-Three sizes of netting for
overlay camo patterns
-Various clamps for holding
netting in place
High Heat Tape:
Used for masking areas where
coating is not desired. Avail-
able in sizes 1/4” to 4”
NIC part # SE-121 through
SE-127
8
WWW.CERAKOTEGUNCOATINGS.COM
Phase 5: gas-out
Gas-Out:
After parts are racked, heat the parts in the oven at 250 degrees Fahrenheit (F) for
30 minutes to drive off any remaining solvents or contaminants.
Remove the parts from the oven
and allow them to cool. If you see
any “wetness,” or other indica-
tion that oil was driven out of the
part, re-clean by soaking in the
degrease tank and reheat for an
additional thirty minutes. Any con-
tamination from this point onward
will result in a less than sastisfac-
tory finish. Be careful, and take
your time. If further degreasing is
required, repeat as necessary un-
til no wetness (oil) is visible.
9
WWW.CERAKOTEGUNCOATINGS.COM
Selecting the right series
for the application
Selecting The Right Cerakote Series for the
Application.
Cerakote™ H-Series:
H-Series is the most durable of the standard Cerakote™ product and provides the best
performance in hardness, wear, scratch resistance, adhesion and rust resistance. It can
withstand temperatures up to 400 degrees F and comes in over 60 colors. H-Series is
a thermal cure finish and therefore should not be applied to optics and other items or
substrates which cannot be cured at the required temperatures. (See cure schedule
table, Page 16.)
Cerakote™ C-Series:
C-Series should ONLY be used for high-temp applications up to 1700 degrees F, such
as suppressors and machine gun barrels. C-Series is available in a wide range of colors
to match the overall finish requirement of the firearm or weapons system. C-Series is
used to coat scopes and other optics, as well as fiberglass, polymer and other substrates
which cannot be thermally cured.
10
WWW.CERAKOTEGUNCOATINGS.COM
Phase 6: coating prep
Coating Preparation:
Prepare the Cerakote for application. Begin by shaking the bottle until the coating is
completely mixed, then shake some more for good measure. Determine how much Cera-
kote you intend to use before mixing (see table 1 pg. 10) Pot life for mixed Cerakote is
approximately two hours in an open container, and as much as four hours in a closed
container. Consequently, mix only what you intend to use, to avoid wasted coating. (see
usage chart pg. 10)
1.) Pour the desired quantity 2.) Add hardener. Use table 1 3.) Mix thoroughly with a
of Cerakote into the graduated pg. 10 to determine Cerakote stir stick.
cylinder. to hardener ratio for finish
type.
4.) Pour mixed coating
through a disposable
automotive type paint filter,
or a reusable filter shown
(NIC Part # SE-139)
11
WWW.CERAKOTEGUNCOATINGS.COM
Phase 6: coating prep
Coating Preparation Continued:
NOTE: If the proportions of Cerakote to Hardener are incorrect, or the combination of
Product and Hardener are not thoroughly mixed, the final product will be splotchy at best
because the coating mixture was uneven, and your work will be wasted.
Table 1
Cerakote / Hardener Ratio
Matte Finish 24:1
Satin Finish 18:1
Semi Gloss 16:1
Table 2 (18:1 Ratio)
Cerakote / Hardener Ratio Usage Chart
Firearm Cerakote Hardener
mL/cc mL/cc
Pistol 36 2
Rifle 72 4
**Read and follow the instructions that come with the color(s) you are using.
Some Product to Hardener ratios are different depending on the color used.
12
WWW.CERAKOTEGUNCOATINGS.COM
Phase 7: Spraying
Spraying
CAUTION:
Spray in a well-ventilated area, wear a respirator, protective gloves and safety glasses.
Refer to the MSDS for additional safety and handling information
Final Checklist Before Spraying:
• Plug or mask off all parts that are not to be coated. Remember Cerakote is applied
at .001” which is very thin, most areas do not require masking, however, if you are
unsure, contact NIC for assistance.
• Ensure all parts to be coated are hung securely, ensuring parts do not touch
anything during the application process
• Do not coat springs as it is not recommended to heat springs during the curing
process.
• Plug the bore to prevent overspray inside the bore.
PRACTICE:
Practice spraying on a piece of metal before going on to your final project.
A particularly good exercise is to spray and cure a few machine screws and matching
nuts. You should be able to screw the nut onto the machine screw without difficulty. If
you can’t, you may be spraying too heavily.
13
WWW.CERAKOTEGUNCOATINGS.COM
Phase 7: mixing & Spraying supplies
Recommended Mixing
& Spraying Supplies
NIC recommends the following products for the best results during the coating
prep and application process
Graduated Cylinder:
NIC Part # SE-147A (100 ml)
or NIC Part # SE-147B (50 ml)
Depending on coating volume.
NIC suggests using a 100M/L graduated cylinder for
accurate ratio measurements of Cerakote to hardener.
IWATA LPH-80:
NIC Part # SE-138
• Miniature, center post gravity feed spray gun is a full-
featured HVLP gun with spray characteristics similar to
Iwata’s popular RG-3 gun.
• Using only 1.8 cfm at 13 psi, this low-air-consumption gun
provides high atomization with precise control of the spray
pattern and a minimum of overspray.
• Features adjustable spray pattern from round to full-fan
shape.
• A stainless-steel nozzle, paint passage and heat-tempored
needle ensure long-lasting, peak-performance spraying.
• Uses the reliable and easy-to-service cartridge-style
“air-valve” set, which can be serviced outside the gun and
easily placed back into the gun body.
• Its 4 oz. (110 ml) stainless-steel gravity cup is center-
mounted and rotates, allowing for spraying horizontally,
vertically or underneath surfaces.
• Unlike siphon-feed guns, this gravity-feed cup will work
with small amounts of paint without spitting
• Spray pattern is from 1/8” to 6” (0.3 cm to 15.24 cm) 14
WWW.CERAKOTEGUNCOATINGS.COM
Phase 7: spraying
Spraying Continued:
Blow off parts with dry compressed air to
make sure there is no trapped media in holes
or pockets. Sand or other media left behind
will cause surface defects.
Start spraying in the most difficult area of each
part, then progress and finish to the easier
areas. This should help avoid runs and thin
spots.
15
WWW.CERAKOTEGUNCOATINGS.COM
Phase 7: spraying
Spraying Continued:
When spraying, strive for even coverage.
You are seeking a 0.5 to 1.0 mil coating
(0.0005” to 0.001”). Spray with sufficient
volume that the Cerakote doesn’t “flash
off” before the coating hits the part.
When spraying, the part should appear
wet but not so wet that it wants to run.
TIP:
• Do not spray with a wide pattern.
Doing so may cause dry spray or a
rough finish.
Example of “wetting out” the part 16
WWW.CERAKOTEGUNCOATINGS.COM
Phase 7: spraying
Spraying Continued:
After each part is coated, set it aside
for about five to ten minutes. Cerakote
will still be wet to the touch until it is
oven cured.
If you touch any coated parts before
curing, the coating will smudge and will
have to be refinished.
“MISTAKES”
If a mistake is made during spraying, e.g., a run, don’t attempt to wipe down the part
and re-spray. Instead, rinse the part with cleaning solvent or acetone to completely
remove the uncured coating. Re-blast the part, dry in the oven, blow off, and re-spray.
Cleaning Up:
Clean your tools with acetone. Contact NIC with questions regarding cleaning solvent
compatibility. Discard any unused “mixed” Cerakote according to local and state
regulations. Do not return any unused “mix” to the bottle.
17
WWW.CERAKOTEGUNCOATINGS.COM
Phase 8: curing
Oven Cure:
Carefully move each part into the oven and cure at 250 degrees (F) for two hours. If you
must hurry the process, curing for 45 minutes at 300 degrees (F) is an alternative cure
schedule. If the part(s) being coated are heat sensitive, 150 to 180 degrees (F) for two
hours will adequately cure plastic, polymer, wood and composite parts.
After curing is completed, remove the parts from the oven and allow the parts to cool.
Once parts are cool enough to handle, the firearm can be reassembled.
**CAUTION**
If you are unsure as to the temperature stability of your parts, contact the manufacturer
prior to oven cure.
Cure Schedule Table
Material Temperature Time
Metal
(Standard)
250 Degrees F 2 Hours
Metal 300 Degrees F 45 Minutes
(Quick Cure)
Metal
(Flash, when 180 Degrees F 15 Minutes
using stencils)
Wood,
Plastic 150-180 2 Hours
or Degrees F
Polymer
TIP:
• “Flashing” parts allows for partial curing at 180-200 degrees (F) for 15 minutes.
This technique is used when applying and removing stencils.
18
WWW.CERAKOTEGUNCOATINGS.COM
training program
Cerakote™ Firearm Coating Training Program
NIC Industries offers the only one-on-one training program for Cerakote™ Firearm Coating. With indi-
vidual training, our instructors speak with the customers prior to the training course to custom design
each class to meet the specific needs of each customer. Customers can apply any of NIC’s industry
leading firearm coatings on their own parts, or parts supplied by NIC. Courses are taught at NIC’s
training facility in White City, Oregon, or onsite*. While every class is custom tailored to meet each
customer’s needs, below are topics typically covered in most courses.
Training Topics
• Metal Prep • Problem solving and troubleshooting defects
• Out-gassing • Proper equipment and operation
• Racking Techniques • Re-works
• Coating selection for various applica- • Cost analysis
tions
• Marketing
• Basic to advanced ceramic application
• Proper curing techniques and schedules
*Contact NIC for further information about on-site training at 866-774-7628.
Class Location
NIC Industries, Inc. is located at 7050 Sixth Street, White City, OR, 97503. White City is located in
Southern Oregon approximately 5 miles from Medford, Oregon, and approximately 280 miles from
Portland, Oregon.
Transportation
Rogue Valley International Airport (MFR) is located 6 miles from NIC and provides daily flights from
several major west coast airports. All major rental car companies are located at the Rogue Valley
International Airport.
Lodging
NIC has negotiated discounted rates with several hotels in close proximity to our facility. Information
can be found at http://www.cerakoteguncoatings.com/resource/downloads/
19
WWW.CERAKOTEGUNCOATINGS.COM
technical information
H-Series CERAKOTE™ Firearm Coatings
The unique formulation used for Cerakote™ firearm coating enhances a number of physical perfor-
mance properties including: abrasion/wear resistance, corrosion resistance, chemical resistance,
impact strength, and hardness. Each of these properties is rigorously tested to guarantee that
Cerakote™ products remain at the forefront of the firearm coatings market. For this study, the
performance properties of Cerakote™ H-146 Graphite Black were compared to the products of two
firearm coatings competitors, denoted as C1 and C2. Each coating was evaluated on nine important
aspects including performance and cost. These results are summarized in table 1, shown below,
and a more extensive description is given in the following paragraphs.
Table 1. Performance comparison of Cerakote™ H-146 to competitor firearm coatings, C1 and C2.
Specification Cerakote™ C1 C2
Taber Abrasion Testing Wear cycles per mil: Wear cycles per mil: Wear cycles per mil:
(ASTM D4060) 6000 597 418
Corrosion Testing Corrorsion-free at: Onset of Corrosion: Onset of Corrosion:
(ASTM B117) 1000 hours 100 hours 45 hours
Pencil Hardness
(ASTM D3363)
9h 9h 7h
Adhesion Cross-Cut Tape
(ASTM D3359)
5b 5b 5b
Mandrel Bend
(ASTM D522) 32% 32% 32%
Impact
(ASTM D2794) 160 inch-lbs 160 inch-lbs 140 inch-lbs
Chemical Resistance Excellent Excellent Good
Theoretical Coverage
(ft2/gal at 1 mil thickness) 478 250* 321
Cost ($/ft )2
$0.62/ft2 $0.65/ft2 $0.99/ft2
VOC Compliance VOC compliant in all Non Compliant Non Compliant
50 states
*Theoretical coverage if applied according to manufacturers specifications of 0.5 mil.
See all the test results at http://www.cerakoteguncoatings.com/testing/
20
WWW.CERAKOTEGUNCOATINGS.COM
technical information
21
WWW.CERAKOTEGUNCOATINGS.COM
technical information
22
WWW.CERAKOTEGUNCOATINGS.COM
technical information
23
WWW.CERAKOTEGUNCOATINGS.COM
technical information
24
WWW.CERAKOTEGUNCOATINGS.COM
DIVISIONS OF NIC INDUSTRIES, INC.
TURN UP THE HEAT WITH CERAKOTE HIGH TEMP.
TM
TM
CERAKOTE IS ALSO THE INDUSTRY LEADER IN EXHAUST COATINGS.
www.CerakoteHighTemp.com
IF YOU CAN CERAKOTE, YOU CAN POWDER COAT.
TM
PRISMATIC POWDERS OFFERS THE WORLDS LARGEST SELECTION
OF CUSTOM COLORED POWDER COATINGS.
www.PrismaticPowders.com
GET THE LATEST NEWS, UPDATES,
VIDEOS,
OFFERS,
& MORE
25
WWW.CERAKOTEGUNCOATINGS.COM
contact information
Need Help?
At any point during the Cerakote application you have a question,
please contact Cerakote Firearm Coatings at:
NIC Industries, Inc.
7050 Sixth Street
White City, OR 97503
Phone: 541-826-1922
Toll Free: 866-774-7628
Email: info@nicindustries.com
Web: www.CerakoteGunCoatings.com
Fax: 541-826-6372
You can also view training videos online at:
www.YouTube.com/nictraining
Follow us on Facebook at:
www.Facebook.com/CerakoteGunCoatings
Subscibe to Cerakote’s Newsletter via www.CerakoteGunCoatings.com
to receive Cerakote news, information, and events.
26
WWW.CERAKOTEGUNCOATINGS.COM
FINISH STRONG
TM
Cerakote Firearm Coatings
A Division of NIC Industries, INC.
866-774-7628
www.CerakoteGunCoatings.com